MAQUINAS RELACIONADAS

FAQS

What type of water is the Amazon 650 XE-V23 suitable for?
It is a submersible electric pump especially indicated for dirty water. It allows the passage of impurities up to 35 mm in diameter and is suitable for sludge, so it is used to empty wells, flooded basements or tanks with sediments.
What type of water is the Amazon 650 XE-V23 designed for?
It is a submersible electric pump especially indicated for dirty water. It allows the passage of impurities up to 35 mm in diameter and is suitable for sludge, so it is suitable for draining flooded basements, pits or wells with water with sediment.
What flow rate and delivery head does this submersible pump offer?
It provides a maximum and nominal flow rate of 13,000 l/h and a maximum delivery head of 7.5 meters, values designed to drain large volumes of water in a short time.
Can it vacuum water with mud or suspended solids?
Yes, it is approved as suitable for sludge and allows the passage of impurities up to 35 mm in diameter, which makes it suitable for dirty water with sediments.
How deep can you submerge and how high does it propel the water?
It supports a maximum immersion of 7 meters and reaches a delivery height of up to 7.5 meters, with a maximum flow rate of 13,000 l/h and a minimum suction height of 35 mm.
What flow rate and delivery head does it provide?
It has a 750 W (1.01 HP) motor capable of moving up to 13,000 l/h and raising water up to 7.5 m high. This allows you to empty large volumes of water in a short time during bailing jobs.
What immersion depth does it allow and how much water does it leave at the bottom?
It can work submerged up to 7 meters deep and has a minimum suction height of 35 mm, determined by the geometry of the suction body.
How deep can it dive?
It supports a maximum immersion depth of 7 m and has IPX8 protection, certified for continuous submerged use. Even so, it is advisable to respect the times and working conditions indicated in the manual.
Does it need to be monitored or does it turn on and off by itself?
It incorporates a buoy system that acts as an automatic on and off switch depending on the water level, allowing it to be used without constant supervision during bailing.
How does automatic buoy start work?
It incorporates a float that acts as an on and off switch depending on the water level. When the level rises, the pump starts; When it descends below the threshold, it stops, preventing it from working without water.
How is the on and off controlled?
The start is manual with a buoy: the integrated float acts as an automatic switch depending on the water level, so all you have to do is connect it and place the cable at the desired height.
What electrical power does it consume and at what voltage does it operate?
It has a 0.75 kW (1.01 HP) Garland AC electric motor that connects to the 230 V and 50 Hz home network, without the need for three-phase installation.
Why is the casing made of stainless steel?
The stainless steel chassis provides greater resistance to corrosion in continuous contact with dirty water and prolongs the useful life of the equipment compared to unprotected plastic or cast iron casings.
What material is the case made of and what degree of protection does it have?
The chassis is made of stainless steel, which improves its resistance to water with impurities. It has an IPX8 protection rating, typical of equipment designed for continuous immersion.
What diameter is the outlet and what hose to use?
The discharge outlet is 32 mm (1 1/4"). To avoid losing flow, it is advisable to use a discharge hose with a corresponding diameter and keep the route as straight and short as possible to the discharge point.
What advantage does the stainless steel casing provide?
The stainless steel chassis offers better corrosion resistance than plastic materials when the pump works submerged in water with impurities or sediments, which helps to extend its useful life in frequent drains.
What measurements and weight do you have to evaluate its handling?
In use it occupies 20 x 28 x 29.5 cm and the packaged set weighs 6.3 kg, making it easy to lower it into wells or manholes by holding it by the integrated carrying handle.
What diameter is the discharge outlet to connect the hose?
The discharge outlet is 32 mm (1 1/4" thread), so it is advisable to choose hose and fittings compatible with this measurement so as not to throttle the flow.